Difference between revisions of "Multimeters"

From Open Source Solar Project
Jump to navigation Jump to search
Line 1: Line 1:
 
[[Category:Basics]]
 
[[Category:Basics]]
Multimeters are the most important tool one has when working with electricity. A multimeter allows you to measure all of the important characteristics of a circuit or electrical system, which enables you to work safely and verify if a circuit is working correctly. There are many different types of multimeters that offer a variety of different functions. They range in cost dramatically as well. All multimeters, even cheap ones, should be able to perform the basic measurements that are required to do electrical work: voltage, current, resistance, conductivity and frequency. That being said, it is important to make sure that the multimeter you are using is rated for use with the highest potential voltage and current that you intend to measure. If a multimeter is not rated to function under the conditions of use, it could destroy the multimeter and potentially cause severe harm. Multimeters are classified into various categories that inform users about their ability to handle excess voltages and current. These ratings go from the lowest rating being Category I (for use with small electronics with limited current/voltage sources) to Category IV (for use at the connection to the utility grid and all outdoor conductors)<ref name="lightning"> Fluke Application Note on multimeter categories https://content.fluke.com/promotions/promo-dmm/0518-dmm-campaign/dmm/fluke_dmm-chfr/files/safetyguidelines.pdf</ref>.outdoor conductors coming from the utility grid). For small off-grid PV systems '''at least''' a Cat II - 600V multimeter is recommended and should be fairly cheap.
+
Multimeters are the most important tool one has when working with electricity. A multimeter allows you to measure all of the important characteristics of a circuit or electrical system, which enables you to work safely and verify if a circuit is working correctly. There are many different types of multimeters that offer a variety of different functions. They range in cost dramatically as well. All multimeters, even cheap ones, should be able to perform the basic measurements that are required to do electrical work: voltage, current, resistance, conductivity and frequency. That being said, it is important to make sure that the multimeter you are using is rated for use with the highest potential voltage and current that you intend to measure. If a multimeter is not rated to function under the conditions of use, it could destroy the multimeter and potentially cause severe harm. Multimeters are classified into various categories that inform users about their ability to handle excess voltages and current. These ratings go from the lowest rating being Category I (for use with small electronics with limited current/voltage sources) to Category IV (for use at the connection to the utility grid and all outdoor conductors)<ref name="lightning"> Fluke Application Note on multimeter categories https://content.fluke.com/promotions/promo-dmm/0518-dmm-campaign/dmm/fluke_dmm-chfr/files/safetyguidelines.pdf</ref>.outdoor conductors coming from the utility grid). For small off-grid PV systems ''at least'' a Cat II - 600V multimeter is recommended and should be fairly cheap.
  
 
==Functions of a multimeter==
 
==Functions of a multimeter==
Line 7: Line 7:
 
*To check if there is voltage in a circuit before beginning to work.
 
*To check if there is voltage in a circuit before beginning to work.
 
*To test the performance of a component in a PV system. Is the voltage within an acceptable range given the conditions? The battery should be fully charged, what is its voltage?
 
*To test the performance of a component in a PV system. Is the voltage within an acceptable range given the conditions? The battery should be fully charged, what is its voltage?
*To identify where a problem is in a system by troubleshooting by testing various circuits and components in the system such as the battery, PV source, inverter, outlets, or light sockets.  
+
*To identify where a problem is in a system by troubleshooting by testing various circuits and components in the system such as the battery, PV source, inverter, outlets, or light sockets.
 +
<gallery widths=100px>
 +
File:VoltagesymbolDC.png|'''DC Voltage'''
 +
File:VoltagesymbolAC.png|'''AC Voltage'''
 +
</gallery>
 +
 
 
===Current===
 
===Current===
 
Not all multimeters can take AC and DC current measurements, but for work with PV systems it is important to find one that does. There are two different ways to measure current with a multimeter, this is explored in the section -[[Multimeters#Types of multimeters|Types of multimeters]]. When working with a PV system, current measurements are typically taken for teh following reasons:
 
Not all multimeters can take AC and DC current measurements, but for work with PV systems it is important to find one that does. There are two different ways to measure current with a multimeter, this is explored in the section -[[Multimeters#Types of multimeters|Types of multimeters]]. When working with a PV system, current measurements are typically taken for teh following reasons:
Line 14: Line 19:
 
*To understand power consumption for a system or various loads within a system.
 
*To understand power consumption for a system or various loads within a system.
 
*To understand the flow of electricity. If there is a heavy load on the system, where is it all going?
 
*To understand the flow of electricity. If there is a heavy load on the system, where is it all going?
 +
<gallery widths=100px>
 +
File:CurrentsymbolDC.png|'''DC Current'''
 +
File:CurrentsymbolAC.png|'''AC Current'''
 +
</gallery>
 
===Resistance===
 
===Resistance===
 
All components of an electrical system have some amount of internal restistance, but also resistance relative to other components of the system. When working with a PV system, resistance mesasurements are typically taken for the following reasons:
 
All components of an electrical system have some amount of internal restistance, but also resistance relative to other components of the system. When working with a PV system, resistance mesasurements are typically taken for the following reasons:
 
*To ensure that a conection made in the system has a low enough resistance to function properly. High resistance connections can create heat and fires.
 
*To ensure that a conection made in the system has a low enough resistance to function properly. High resistance connections can create heat and fires.
 
*To ensure that there is a high resistance between the earth/ground and components of the system that should not have a connection of any kind to the ground.
 
*To ensure that there is a high resistance between the earth/ground and components of the system that should not have a connection of any kind to the ground.
 +
<gallery widths=100px>
 +
File:ohmsymbol.png|'''Resistance'''
 +
</gallery>
 
===Conductivity===
 
===Conductivity===
 
A conductivity check is a simplified resistance check. If a connection has a sufficiently low resistance - below a certain value that is set inside the multimeter - then the multimeter will emit a sound. If there is a high resistance between the two points of measurement, the multimeter will do nothing. Conductivity checks are performed for the same reasons as resistance checks, but it enables you to work faster.
 
A conductivity check is a simplified resistance check. If a connection has a sufficiently low resistance - below a certain value that is set inside the multimeter - then the multimeter will emit a sound. If there is a high resistance between the two points of measurement, the multimeter will do nothing. Conductivity checks are performed for the same reasons as resistance checks, but it enables you to work faster.
 +
<gallery widths=100px>
 +
File:Continuitysymbol.png|'''Continuity'''
 +
</gallery>
 
===Frequency===
 
===Frequency===
 
Frequency is a property of AC systems. Inverters in an off-grid system should be operating within a specific frequency range, a frequency check can tell us that they are outside of this range and that there is a problem. A frequency that is out range can cause issues with appliances.
 
Frequency is a property of AC systems. Inverters in an off-grid system should be operating within a specific frequency range, a frequency check can tell us that they are outside of this range and that there is a problem. A frequency that is out range can cause issues with appliances.
 +
<gallery widths=100px>
 +
File:Frequencysymbol.png|'''Frequency'''
 +
</gallery>
 
==Types of multimeters==
 
==Types of multimeters==
 
[[File:Multimeter200927.png|frame|center|'''Multimeter types:''' ''Left'' - Clamp meter. ''Center'' - Traditional autoranging handheld multimeter. ''Right'' - Probes]]
 
[[File:Multimeter200927.png|frame|center|'''Multimeter types:''' ''Left'' - Clamp meter. ''Center'' - Traditional autoranging handheld multimeter. ''Right'' - Probes]]

Revision as of 18:26, 27 September 2020

Multimeters are the most important tool one has when working with electricity. A multimeter allows you to measure all of the important characteristics of a circuit or electrical system, which enables you to work safely and verify if a circuit is working correctly. There are many different types of multimeters that offer a variety of different functions. They range in cost dramatically as well. All multimeters, even cheap ones, should be able to perform the basic measurements that are required to do electrical work: voltage, current, resistance, conductivity and frequency. That being said, it is important to make sure that the multimeter you are using is rated for use with the highest potential voltage and current that you intend to measure. If a multimeter is not rated to function under the conditions of use, it could destroy the multimeter and potentially cause severe harm. Multimeters are classified into various categories that inform users about their ability to handle excess voltages and current. These ratings go from the lowest rating being Category I (for use with small electronics with limited current/voltage sources) to Category IV (for use at the connection to the utility grid and all outdoor conductors)[1].outdoor conductors coming from the utility grid). For small off-grid PV systems at least a Cat II - 600V multimeter is recommended and should be fairly cheap.

Functions of a multimeter

Voltage

Any multimeter that is to be used have the ability to measure both DC and AC. It is important to understand the type of current that is going to be measured, as using the wrong setting can lead to a false reading which can be misleading and dangerous. A multimeter will have a dial that allows the user to select between AC and DC, which will be identified using the common symbols seen below. When working with a PV system, voltage is typically measured for the following reasons:

  • To check if there is voltage in a circuit before beginning to work.
  • To test the performance of a component in a PV system. Is the voltage within an acceptable range given the conditions? The battery should be fully charged, what is its voltage?
  • To identify where a problem is in a system by troubleshooting by testing various circuits and components in the system such as the battery, PV source, inverter, outlets, or light sockets.

Current

Not all multimeters can take AC and DC current measurements, but for work with PV systems it is important to find one that does. There are two different ways to measure current with a multimeter, this is explored in the section -Types of multimeters. When working with a PV system, current measurements are typically taken for teh following reasons:

  • To check if there is any current flowing in a circuit before beginning to work.
  • To understand how the PV module or array is functioning. How much current is it producing under the conditions?
  • To understand power consumption for a system or various loads within a system.
  • To understand the flow of electricity. If there is a heavy load on the system, where is it all going?

Resistance

All components of an electrical system have some amount of internal restistance, but also resistance relative to other components of the system. When working with a PV system, resistance mesasurements are typically taken for the following reasons:

  • To ensure that a conection made in the system has a low enough resistance to function properly. High resistance connections can create heat and fires.
  • To ensure that there is a high resistance between the earth/ground and components of the system that should not have a connection of any kind to the ground.

Conductivity

A conductivity check is a simplified resistance check. If a connection has a sufficiently low resistance - below a certain value that is set inside the multimeter - then the multimeter will emit a sound. If there is a high resistance between the two points of measurement, the multimeter will do nothing. Conductivity checks are performed for the same reasons as resistance checks, but it enables you to work faster.

Frequency

Frequency is a property of AC systems. Inverters in an off-grid system should be operating within a specific frequency range, a frequency check can tell us that they are outside of this range and that there is a problem. A frequency that is out range can cause issues with appliances.

Types of multimeters

Multimeter types: Left - Clamp meter. Center - Traditional autoranging handheld multimeter. Right - Probes

Traditional handheld multimeter

These are the most common and economical multimeters on the market. For a low price they can perform many different functions and, if it is a decent brand, should be fairly accurate. These multimeters rely on probes to take all of measurements. This means that the amount of current that they can measure, as it has to pass through the multimeter, is often limited to 10-15A. There is an internal fuse that will be destroyed if one attempts to pass excess current through the multimeter. This means that one cannot take current measurements of circuits for which the amount of current flowing is not already known. Nor can one take measurements of asource that can supply high amounts of current - like an outlet or a battery - as the multimeter provides a low resistance path for the current to pass through. If measuring currents near or in excess of 10A may be required, then it is necessary to get a clamp meter.

These meters come in two types:

Manual-ranging

This type of multimeter requires the user to select the maximum voltage, current, or resistance in order to take a measurement. If too high of a range is used, it will lead to inaccurate measurements. If too low of a range is used, the multimeter will give an error. The cheapest multimeters are manual-ranging. For example:

  • Example 1: You would like to take a voltage measurement of a circuit that you suspect to be 220V AC. Your options on the multimeter are 120V AC, 250VAC, 500VAC. What is the proper range for taking this measurement?
Answer: 250V AC. The 120V AC setting will produce an error. The 500V AC setting may produce an inaccurate reading. The 250V AC setting will be able to provice the most accurate measurement.

One technique that works with a manual ranging multimeter, is to start at the highest range, get a measurement and then work your way down to the lowest range capable of measuring a value in that range until there is an error.

Auto-ranging

This type of multimeter does the work of selecting the range itself and can save time for the user. For a slightly higher price, one can purchase an auto-ranging multimeter. Auto-ranging multimeters cost slightly more than their manual-ranging counterparts, but the additional cost is worth it if you will be using the meter frequently.

Clamp meters

Clamp meters are auto-ranging and share all of the basic functions of a traditional handheld multimeter, but they enable current measurements above 10A to a certain limit, typically around 300-400A. The multimeter performs current measurements by measuring the current that is flowing in a wire based upon the electro-magnetic field that it generates. To take a measurement one simply passes one wire of a circuit through the jaws of the clamp, which can easily be opened and closed by a button the side. It is important to only pass one wire of a circuit through the clamp because if both wires are passed through the currents will cancel out.

A clamp meter is extremely useful, easy to use and significantly safer than a traditional handheld multimeter. The meters do cost slightly more, but the additional cost is is worth it if you will frequently take current measurements.

Taking measurements with a multimeter

Notes