Difference between revisions of "Load evaluation"

From Open Source Solar Project
Jump to navigation Jump to search
 
(55 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
[[Category:Site evaluation]]
 
[[Category:Site evaluation]]
−
The load evaluation involves gathering information on loads which will serve as the basis for the rest of the system design process. Power ratings and usage estimates for necessary and potential loads are gathered into a table - one for direct current and one for alternating current. It is important to use maximum values for estimated usage to ensure that the system is adequately sized. It may be necessary to perform an estimation of this sort for each month of the year if loads, esimated usage, or solar resource vary frequently throughout the year. Usage in the charts below is therefore estimated on a monthly basis so that it can be easily used in a [[Load and solar resource comparison|load and solar resource comparison]] if necessary. The monthly total is typically calculated by  estimating weekly usage and multiplying by 4 to get a monthly total. This process works well for loads that are used everyy day or those that are used only occasionally, but it is necessary to be careful with loads that are used for consecutive days during the week. If a load is used during all 5 business days of the week it should be treated as operating 7 days out of the week as removing 2 days a week from will reduce the average energy requirement, but in reality the system will be required to store and generate the full energy requirement on most days.  
+
<languages />
 +
<translate>
 +
<!--T:1-->
 +
The load evaluation involves gathering information on loads which will serve as the basis for the rest of the system design process. Power ratings and usage estimates for necessary and potential loads are gathered into tables - one for direct current and one for alternating current. It is important to use maximum values for estimated usage to ensure that the system is adequately sized. It may be necessary to perform an estimation of this sort for each month of the year if loads, estimated usage, or solar resource vary frequently throughout the year. This process is covered in [[Special:MyLanguage/Load and solar resource comparison|Load and solar resource comparison]] and values that result from this process should be used to design the system. In the tables below usage is estimated on a weekly basis. This process works well for loads that are used every day or large loads that are only used occasionally, but it is necessary to be careful in two cases:
 +
#With loads that are used for multiple consecutive days during the week. If a load is used during all 5 business days of the week it should be treated as operating 7 days out of the week as removing 2 days a week will reduce the average energy requirement, but in reality the system will be required to generate and store the full energy requirement on most days.
  
−
When designing any system it is almost always necessary to explore various different designs with varying loads and usage patterns to arrive at the best balance between cost and budget.
+
<!--T:2-->
 +
#With systems that see heavy usage only 1 or 2 days out of the week. Inputting 1 or 2 days for all loads will lead to a system with PV source and energy storage system that are undersized. In this case, it is recommended that the days of usage be set to 4 or 5 days.  
  
−
====Additional considerations====
+
<!--T:3-->
 +
When designing any system, it is almost always necessary to explore various different designs with varying loads and usage patterns to arrive at the best balance between cost and budget.
 +
 
 +
====Additional considerations==== <!--T:4-->
 +
 
 +
<!--T:5-->
 
*The make, model, and power rating of any loads currently present at the site should be documented. Photos are very useful.
 
*The make, model, and power rating of any loads currently present at the site should be documented. Photos are very useful.
−
*If the system design is going to incorporate loads that have not yet been purchased, guidance should be provided about the value and importance of purchasing [[Energy efficient loads|energy efficient loads]].
 
−
*This process can be difficult in locations that do not currently have electricity or that have users that do not have experience with electricity beforehand. In these cases there is a tendency to over-estimate and under-estimate appliance usage depending on the individual. In these cases, more responsibility falls upon the person performing the load evaluation and the system designer to provide guidance and accurate estimates.
 
−
*Potential projects that do not currently have an electrical system will also require additional evaluation and design work to ensure that the building will have adequate outlets for (power receptacles) and [[Lighting|lighting]] for the intended use of each room.
 
  
−
==DC load evaluation==
+
<!--T:6-->
−
Typical direct current loads include lights, cell phones, radios, and DC refrigerators. If a system incorporates an [[Inverter|inverter]], it is important that its [[Inverter#Idle consumption|idle consumption]] is included in the DC load evaluation.
+
*If the system design is going to incorporate loads that have not yet been purchased, guidance should be provided about the value and importance of purchasing [[Special:MyLanguage/Energy efficient loads|energy efficient loads]].
 +
 
 +
<!--T:7-->
 +
*This process can be difficult in locations that do not currently have electricity or that have users that do not have experience with electricity beforehand. In these cases, there is a tendency to over-estimate and under-estimate appliance usage depending on the individual. The result is that more responsibility falls upon the person performing the load evaluation and the system designer to provide guidance and accurate estimates.
 +
 
 +
<!--T:8-->
 +
*Potential projects that do not currently have an electrical system will also require additional evaluation and design work to ensure that the building will have adequate outlets for (power receptacles) and [[Special:MyLanguage/Lighting|lighting]] for the intended use of each room.
 +
 
 +
==DC load evaluation== <!--T:9-->
 +
 
 +
<!--T:10-->
 +
Typical direct current loads include lights, cell phones, radios, and DC refrigerators. If a system incorporates an [[Special:MyLanguage/Inverter|inverter]], it is important that its [[Special:MyLanguage/Inverter#Idle consumption|idle consumption]] is included in the DC load evaluation.
  
 +
====Step 1: Fill out DC load chart==== <!--T:11-->
 +
 +
<!--T:12-->
 
{| class="wikitable" style="text-align: center;"
 
{| class="wikitable" style="text-align: center;"
 +
|
 +
|
 +
|
 +
|
 +
|
 +
|
 +
!colspan="3"|April - September
 +
!colspan="3"|October - March
 +
|-
 
!#
 
!#
 
!Load
 
!Load
 
!Quantity
 
!Quantity
 
!Watts
 
!Watts
−
![[Duty cycle]]
+
!Total watts
−
!Total Watts
+
![[Special:MyLanguage/Duty cycle|Duty cycle]]
 
!Hours per day
 
!Hours per day
−
!Days per month
+
!Days per week
−
!Average Watt-hours per day
+
!Average daily DC watt-hours
 +
!Hours per day
 +
!Days per week
 +
!Average daily DC watt-hours
 
|-
 
|-
 
|1
 
|1
−
|Cree 5W LED
+
|
−
|4
+
|
−
|5W
+
|
−
|1
+
|
−
|20W
+
|
−
|5 hours
+
|
−
|30 days
+
|
−
|100Wh
+
|
 +
|
 +
|
 +
|
 
|-
 
|-
 
|2
 
|2
−
|Victron 1200W inverter
+
|
−
|1
+
|
−
|8W
+
|
−
|1
+
|
−
|8W
+
|
−
|24 hours
+
|
−
|30 days
+
|
−
|192Wh
+
|
 +
|
 +
|
 +
|
 
|-
 
|-
 
|3
 
|3
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 55: Line 97:
 
|-
 
|-
 
|4
 
|4
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 65: Line 110:
 
|-
 
|-
 
|5
 
|5
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 75: Line 123:
 
|-
 
|-
 
|6
 
|6
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 85: Line 136:
 
|-
 
|-
 
|7
 
|7
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 95: Line 149:
 
|-
 
|-
 
|8
 
|8
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 105: Line 162:
 
|-
 
|-
 
|9
 
|9
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 123: Line 183:
 
|
 
|
 
|
 
|
−
|-
+
|
−
!colspan="8"|Average DC Watt-hour consumption
+
|
−
|292Wh
+
|
 
|}
 
|}
 +
 +
<!--T:13-->
 
*'''Load:''' The make and model or type of load.
 
*'''Load:''' The make and model or type of load.
−
*'''Quantity:''' The number of of that particular load.
+
*'''Quantity:''' The number of the particular load.
−
*'''Watts:''' The power rating in Watts for the load.
+
*'''Watts:''' The power rating in watts of the load.
−
*'''Duty cycle =''' Rated or estimated [[Duty cycle|duty cycle]] for the load.
+
*'''Total watts =''' Quantity × Watts
−
*'''Total watts =''' quantity × Watts
+
*'''Duty cycle =''' Rated or estimated [[Duty cycle|duty cycle]] for the load. If the load has no duty cycle a value of 1 should be used. A load with a duty cycle of 20% would be inputted as .2
−
*'''Hours per day:''' The maximum number of hours that the load(s) will be operated per day.
+
*'''Hours per day:''' The maximum number of hours the load(s) will be operated per day. If the load has a duty cycle 24 hours should be used.
−
*'''Days per month:''' The maximum number of days load(s) will be operated per month.  
+
*'''Days per week:''' The maximum number of days the load(s) will be operated per week.  
−
*'''Average Watt-hours per day =''' Total Watts × Hours per day × Days per month ÷ 30
+
*'''Average daily DC watt-hours =''' Total watts × Duty cycle × Hours per day × Days per week ÷ 7 days
−
*'''Average DC Watt-hour consumption =''' sum of Average Watt-hours per day for all loads
 
  
−
==AC load evaluation==
+
====Step 2: Determine DC energy demand==== <!--T:14-->
−
There are additional considerations that go into performing an AC load analysis because this analysis is used for [[Inverter sizing and selection|inverter sizing and selection]], as well as [[PV source and charge controller sizing and selection]] and [[Energy storage sizing and selection|Energy storage sizing and selection]]. This chart therefore takes into account several other important factors:
 
−
*[[Inverter#Efficiency|Inverter efficiency]]
 
−
*[[Surge loads|Surge loads]]
 
−
*[[Power factor]]
 
  
 +
<!--T:15-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Total average daily DC watt-hours (April - September)
 +
! style="text-align:left;"| = sum of Average daily DC watt-hours for all loads for April - September
 +
|}
 +
 +
<!--T:16-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Total average daily DC watt-hours (October - March)
 +
! style="text-align:left;"| = sum of Average daily DC watt-hours for all loads for October - March
 +
|}
 +
 +
==AC load evaluation== <!--T:17-->
 +
 +
<!--T:18-->
 +
There are additional considerations that go into performing an AC load analysis because this analysis is used for [[Special:MyLanguage/Inverter sizing and selection|inverter sizing and selection]], as well as [[Special:MyLanguage/PV source and charge controller sizing and selection|PV source and charge controller sizing and selection]] and [[Special:MyLanguage/Energy storage sizing and selection|Energy storage sizing and selection]]. This chart therefore takes into account several other important factors:
 +
 +
<!--T:19-->
 +
*[[Special:MyLanguage/Inverter#Efficiency|Inverter efficiency]]
 +
*[[Special:MyLanguage/Surge loads|Surge loads]]
 +
*[[Special:MyLanguage/Power factor|Power factor]]
 +
 +
====Step 1: Inverter efficiency==== <!--T:20-->
 +
 +
<!--T:21-->
 +
The efficiency rating varies between different [[Special:MyLanguage/Inverter|inverters]]. The manufacturers typically give a peak efficiency value that is above 90% (.9), it is recommended that a more conservative value like .8 or .85 be used.
 +
 +
<!--T:22-->
 +
{| class="wikitable" style="text-align: center;"
 +
!|Inverter efficiency
 +
|.85
 +
|}
 +
 +
====Step 2: Fill out AC load chart==== <!--T:23-->
 +
 +
<!--T:24-->
 
{| class="wikitable" style="text-align: center;"
 
{| class="wikitable" style="text-align: center;"
 +
|
 +
|
 +
|
 +
|
 +
|
 +
|
 +
|
 +
|
 +
|
 +
|
 +
! colspan="3"|April - October
 +
! colspan="3"|March - September
 +
|-
 
!#
 
!#
 
!Load
 
!Load
Line 149: Line 255:
 
!Watts
 
!Watts
 
!Total watts
 
!Total watts
−
![[Duty cycle]]
+
![[Special:MyLanguage/Duty cycle|Duty cycle]]
−
![[Surge loads|Surge factor]]
+
![[Special:MyLanguage/Surge loads|Surge factor]]
−
![[Power factor]]
+
![[Special:MyLanguage/Surge loads|Surge watts]]
−
![[Power factor|Apparent power (VA)]]
+
![[Special:MyLanguage/Power factor|Power factor]]
−
![[Power factor|Real power (W)]]
+
![[Special:MyLanguage/Power factor|Volt-amperes (VA)]]
 
!Hours per day
 
!Hours per day
−
!Days per month
+
!Days per week
−
!Average Watt-hours per day
+
!Average daily AC watt-hours
 +
!Hours per day
 +
!Days per week
 +
!Average daily AC watt-hours
 
|-
 
|-
 
|1
 
|1
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 173: Line 285:
 
|-
 
|-
 
|2
 
|2
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 187: Line 302:
 
|-
 
|-
 
|3
 
|3
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 201: Line 319:
 
|-
 
|-
 
|4
 
|4
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 215: Line 336:
 
|-
 
|-
 
|5
 
|5
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 229: Line 353:
 
|-
 
|-
 
|6
 
|6
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 242: Line 369:
 
|-
 
|-
 
|7
 
|7
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 256: Line 386:
 
|-
 
|-
 
|8
 
|8
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 270: Line 403:
 
|-
 
|-
 
|9
 
|9
 +
|
 +
|
 +
|
 
|
 
|
 
|
 
|
Line 296: Line 432:
 
|
 
|
 
|
 
|
−
|-
+
|
−
!colspan="12"|Inverter efficiency
+
|
−
|.85
+
|
 +
|}
 +
 
 +
<!--T:25-->
 +
*'''Load:''' The make and model or type of load.
 +
*'''Quantity:''' The number of the particular load.
 +
*'''Watts:''' The power rating in watts for the load.
 +
*'''Total watts =''' Quantity × watts
 +
*'''Duty cycle =''' Rated or estimated [[Special:MyLanguage/Duty cycle|duty cycle]] for the load. If the load has no duty cycle a value of 1 should be used. A load with a duty cycle of 20% would be inputted as .2
 +
*'''Surge factor =''' Rated or estimated [[Special:MyLanguage/Surge loads|surge factor]] for the load. Common values are between 3-5. If the load does not have a surge requirement a value of 0 should be used.
 +
*'''Surge watts =''' Total watts × Surge factor
 +
*'''Power factor =''' Rated or estimated [[Special:MyLanguage/Power factor|power factor]] for the load.
 +
*'''Volt-amperes (VA) =''' Total watts ÷ Power factor
 +
*'''Hours per day:''' The maximum number of hours the load(s) will be operated per day. If the load has a duty cycle 24 hours should be used.
 +
*'''Days per week:''' The maximum number of days the load(s) will be operated per week.
 +
*'''Average daily AC watt-hours =''' Total watts × Duty cycle ÷ Inverter efficiency (Step 1) × Hours per day × Days per week ÷ 7 days
 +
 
 +
====Step 3: Deteremine AC energy demand==== <!--T:26-->
 +
 
 +
<!--T:27-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Total average daily AC watt-hours (April - September)
 +
! style="text-align:left;"| = sum of Average daily AC watt-hours for all loads for April - September
 +
|}
 +
 
 +
<!--T:28-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Total average daily AC watt-hours (October - March)
 +
! style="text-align:left;"| = sum of Average daily AC watt-hours for all loads for October - March
 +
|}
 +
 
 +
====Step 4: Determine AC power demand==== <!--T:29-->
 +
 
 +
<!--T:30-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Total VA
 +
! style="text-align:left;"| = sum of volt-amperes (VA) of all the loads
 +
|}
 +
 
 +
<!--T:31-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Total VA with surge watts
 +
! style="text-align:left;"| = sum of Surge watts for all loads + Total VA
 +
|}
 +
 
 +
==Total average daily energy demand== <!--T:32-->
 +
 
 +
<!--T:33-->
 +
The total energy demand for the system is the added Average daily DC-watt hours and Average daily AC watt-hours for each time period.
 +
 
 +
<!--T:34-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Average daily watt-hours required (April - September)
 +
! style="text-align:left;"| =  Total average daily DC watt-hours (April - October) + Total average daily AC watt-hours (April - September)
 +
|}
 +
 
 +
<!--T:35-->
 +
{| class="wikitable" border=1 style="width: 80%;"
 +
! style="width: 20%"|Average daily watt-hours required (April - September)
 +
! style="text-align:left;"| =  Total average daily DC watt-hours (October - March) + Total average daily AC watt-hours (October - March)
 
|}
 
|}
 +
 +
==Notes/references== <!--T:36-->
 +
</translate>

Latest revision as of 16:47, 24 March 2021

Other languages:
English • ‎español

The load evaluation involves gathering information on loads which will serve as the basis for the rest of the system design process. Power ratings and usage estimates for necessary and potential loads are gathered into tables - one for direct current and one for alternating current. It is important to use maximum values for estimated usage to ensure that the system is adequately sized. It may be necessary to perform an estimation of this sort for each month of the year if loads, estimated usage, or solar resource vary frequently throughout the year. This process is covered in Load and solar resource comparison and values that result from this process should be used to design the system. In the tables below usage is estimated on a weekly basis. This process works well for loads that are used every day or large loads that are only used occasionally, but it is necessary to be careful in two cases:

  1. With loads that are used for multiple consecutive days during the week. If a load is used during all 5 business days of the week it should be treated as operating 7 days out of the week as removing 2 days a week will reduce the average energy requirement, but in reality the system will be required to generate and store the full energy requirement on most days.
  1. With systems that see heavy usage only 1 or 2 days out of the week. Inputting 1 or 2 days for all loads will lead to a system with PV source and energy storage system that are undersized. In this case, it is recommended that the days of usage be set to 4 or 5 days.

When designing any system, it is almost always necessary to explore various different designs with varying loads and usage patterns to arrive at the best balance between cost and budget.

Additional considerations

  • The make, model, and power rating of any loads currently present at the site should be documented. Photos are very useful.
  • If the system design is going to incorporate loads that have not yet been purchased, guidance should be provided about the value and importance of purchasing energy efficient loads.
  • This process can be difficult in locations that do not currently have electricity or that have users that do not have experience with electricity beforehand. In these cases, there is a tendency to over-estimate and under-estimate appliance usage depending on the individual. The result is that more responsibility falls upon the person performing the load evaluation and the system designer to provide guidance and accurate estimates.
  • Potential projects that do not currently have an electrical system will also require additional evaluation and design work to ensure that the building will have adequate outlets for (power receptacles) and lighting for the intended use of each room.

DC load evaluation

Typical direct current loads include lights, cell phones, radios, and DC refrigerators. If a system incorporates an inverter, it is important that its idle consumption is included in the DC load evaluation.

Step 1: Fill out DC load chart

April - September October - March
# Load Quantity Watts Total watts Duty cycle Hours per day Days per week Average daily DC watt-hours Hours per day Days per week Average daily DC watt-hours
1
2
3
4
5
6
7
8
9
10
  • Load: The make and model or type of load.
  • Quantity: The number of the particular load.
  • Watts: The power rating in watts of the load.
  • Total watts = Quantity × Watts
  • Duty cycle = Rated or estimated duty cycle for the load. If the load has no duty cycle a value of 1 should be used. A load with a duty cycle of 20% would be inputted as .2
  • Hours per day: The maximum number of hours the load(s) will be operated per day. If the load has a duty cycle 24 hours should be used.
  • Days per week: The maximum number of days the load(s) will be operated per week.
  • Average daily DC watt-hours = Total watts × Duty cycle × Hours per day × Days per week ÷ 7 days

Step 2: Determine DC energy demand

Total average daily DC watt-hours (April - September) = sum of Average daily DC watt-hours for all loads for April - September
Total average daily DC watt-hours (October - March) = sum of Average daily DC watt-hours for all loads for October - March

AC load evaluation

There are additional considerations that go into performing an AC load analysis because this analysis is used for inverter sizing and selection, as well as PV source and charge controller sizing and selection and Energy storage sizing and selection. This chart therefore takes into account several other important factors:

Step 1: Inverter efficiency

The efficiency rating varies between different inverters. The manufacturers typically give a peak efficiency value that is above 90% (.9), it is recommended that a more conservative value like .8 or .85 be used.

Inverter efficiency .85

Step 2: Fill out AC load chart

April - October March - September
# Load Quantity Watts Total watts Duty cycle Surge factor Surge watts Power factor Volt-amperes (VA) Hours per day Days per week Average daily AC watt-hours Hours per day Days per week Average daily AC watt-hours
1
2
3
4
5
6
7
8
9
10
  • Load: The make and model or type of load.
  • Quantity: The number of the particular load.
  • Watts: The power rating in watts for the load.
  • Total watts = Quantity × watts
  • Duty cycle = Rated or estimated duty cycle for the load. If the load has no duty cycle a value of 1 should be used. A load with a duty cycle of 20% would be inputted as .2
  • Surge factor = Rated or estimated surge factor for the load. Common values are between 3-5. If the load does not have a surge requirement a value of 0 should be used.
  • Surge watts = Total watts × Surge factor
  • Power factor = Rated or estimated power factor for the load.
  • Volt-amperes (VA) = Total watts ÷ Power factor
  • Hours per day: The maximum number of hours the load(s) will be operated per day. If the load has a duty cycle 24 hours should be used.
  • Days per week: The maximum number of days the load(s) will be operated per week.
  • Average daily AC watt-hours = Total watts × Duty cycle ÷ Inverter efficiency (Step 1) × Hours per day × Days per week ÷ 7 days

Step 3: Deteremine AC energy demand

Total average daily AC watt-hours (April - September) = sum of Average daily AC watt-hours for all loads for April - September
Total average daily AC watt-hours (October - March) = sum of Average daily AC watt-hours for all loads for October - March

Step 4: Determine AC power demand

Total VA = sum of volt-amperes (VA) of all the loads
Total VA with surge watts = sum of Surge watts for all loads + Total VA

Total average daily energy demand

The total energy demand for the system is the added Average daily DC-watt hours and Average daily AC watt-hours for each time period.

Average daily watt-hours required (April - September) = Total average daily DC watt-hours (April - October) + Total average daily AC watt-hours (April - September)
Average daily watt-hours required (April - September) = Total average daily DC watt-hours (October - March) + Total average daily AC watt-hours (October - March)

Notes/references

Retrieved from "http://www.opensourcesolar.org/w/index.php?title=Load_evaluation&oldid=11589"